2 Channel 5V Relay Module With Optocoupler Protection_good quality
₹120.00 Original price was: ₹120.00.₹110.00Current price is: ₹110.00.
(Excluding of GST 18%)
- 5V 2-Channel Relay interface board, and each one needs 15-20mA DriverCurrent
- Equiped with high-current relay, AC250V 10A ; DC30V 10A the 8550 transistor drive, drive ability
- Working voltage 5 V
- Has the fixed bolt hole and easy installation
- Standard interface that can be controlled directly by microcontroller
- Indication LED’s for Relay output status
In stock

2 Channel 5V Relay Module with Optocoupler
- This is a 2 Channel 5V Relay module. It is an Optoisolated module, which means the input of the module can operate from on a supply other than the one used by the module. It is useful in high load and high noise environment. The operating Voltage of the module is 5V. It needs a 5V supply for relay operation.
- The 2 Channel 5V Relay module has a jumper to select the use of optoisolation. If the jumper is used between JD-VCC and VCC pins than the module does not provide opto-isolation and will use the same supply for optocoupler trigger and relay trigger. Whereas, if the Jumper is removed, than the supply for optocoupler trigger can be given separately, which the IN1 and IN2 will be using, and the supply for relay trigger needs to be different, which needs to be connected with Vcc and GND.
- The module has 3 outputs per relay, Normally Open, Common and Normally Closed. The inputs of the module are low triggered, that is it will activate relay when the input signal is low. The module has LEDs for indication of relay operation.
- his is a LOW-Level 5V 2-channel relay interface board, and each channel needs a 15-20mA driver current. It can be used to control various appliances and equipment with a large current. It is equipped with high-current relays that work under AC250V 10A or DC30V 10A. It has a standard interface that can be controlled directly by the microcontroller
- Also Buy 1channel 5v Relay(Click here)
Package Contents
- 1×2 Channel relay module with optocoupler protection
Weight | 30 g |
---|---|
Dimensions | 50 × 40 × 20 cm |
Related products
Arduino Nano Board R3 without USB Cable Compatible with Arduino (Unsoldered) best quality
₹550.00Original price was: ₹550.00.₹390.00Current price is: ₹390.00.Add to cartArduino Nano Board R3 This board is fully compatible with Arduino Nano. It is based on the ATmega328p-AU from the atmel, the SMD version of one used in Arduino Uno. The advantage of this module, is that is very small in size as compared to Arduino Uno. It has integrated USB, and is breadboard friendly. …
Arduino Nano Board R3 without USB Cable Compatible with Arduino (Unsoldered) best qualityRead More
TP5100 4.2v and 8.4v Single/ Double Lithium Battery Charging Board best quality
₹130.00Add to cart- Dual/Single 4.2V/8.4V Li-ion Battery Charger
- Input Voltage: 5V to 18V
- Programmable Charge Current: 0.1A to 2A
- Chip temperature protection, Overcurrent protection, undervoltage protection
- Reverse Battery Shutdown, and short circuit protection
- Trickle, constant current, constant voltage charging 3 states of charging
Arduino Uno R3 ATmega328P Arduino Compatible – DIP (without cable) buy original
₹950.00Original price was: ₹950.00.₹670.00Current price is: ₹670.00.Add to cartArduino Uno R3 ATmega328P The Arduino Uno R3 is a open source micro controller board based on the ATmega328 chip. This Board has 14 digital input/output pins, 6 analog input pins, Onboard 16 MHz ceramic resonator, Port for USB connection, Onboard DC power jack, An ICSP header and a micro controller reset button. It contains …
Arduino Uno R3 ATmega328P Arduino Compatible – DIP (without cable) buy originalRead More
Reviews
There are no reviews yet.