Submersible Mini Water Pump 3-6V DC for Aquariums Fish Tank Pond Fountain Hydroponics Garden good quality
Original price was: ₹160.00.₹80.00Current price is: ₹80.00.
(Excluding of GST 18%)
- Rated voltage: DC 3V or 4.5V.Current: 150-250mA.
- No load of water discharge capacity: 100L / H.
- Quiet Design: Small motors will not produce too much noise.
- Mini Size:Easy to install and remove, small size is for space saving.
- Wide Applicable: This submersible pump can be used for small size aquarium, Fish tank, Pond, tabletop fountains, water gardens and hydroponic systems.
In stock
Submersible Mini Water Pump 3-6V DC
- This is a low cost, small size Submersible mini water Pump Motor which can be operated from a DC 3-5V power supply. It can take up to 100 liters per hour with very low current consumption of 220mA.
- Quiet Design: Small motors will not produce too much noise.
- Mini Size: The mini size makes the pump easy to hide or disguise in the water.
- Wide Applicable: This product can be used for small size aquarium, Fish tank, Pond, tabletop fountains, water gardens and hydroponic systems.
Features:
- Voltage range (V): DC2.5-6v
- Rated voltage: DC3V or 4.5V
- No load of water discharge capacity: 100L / H
- Load rated current: 0.18A
- Use: diving type
- It is a DC pump, 3V pump with DC3-4.5V power supply (Can not be used directly with 220V AC voltage)
- Do not run without water for a long time.
- Note :(Diaphragm water pump ) click here
Package Includes
- 1 x Submersible Mini Water Pump 3-6V DC
| Weight | 35 g |
|---|---|
| Dimensions | 4.3 × 2.4 × 2.4 cm |
Related products
-
Sale!
Arduino Nano Board R3 without USB Cable Compatible with Arduino (Unsoldered) best quality
Original price was: ₹550.00.₹390.00Current price is: ₹390.00.Add to cartArduino Nano Board R3 This board is fully compatible with Arduino Nano. It is based on the ATmega328p-AU from the atmel, the SMD version of one used in Arduino Uno. The advantage of this module, is that is very small in size as compared to Arduino Uno. It has integrated USB, and is breadboard friendly. It does not have any power jack, but still senses, and switch to higher potential power source. Arduino Nano can be said to be a smaller version of Arduino Uno, as its using the same MCU with smaller package. It also provides same functions as provided by Arduino Uno. Apart from that, it has 8 analog input pins instead of 6 analog inputs in Arduino Uno. It also has pinout for the programmer to be connected to the board directly, in case USB is not used for programming. It also has 1 x USART, 1 x SPI, 1 x I2C peripherals. The Arduino Nano has 2 digital interrupt pins, and almost all pins can be used for pin change interrupt. Any pin can wake up MCU on interrupt from sleep mode. It works on 16 Mhz frequency. Micro controller: ATMega328p-AU Input Voltage: 7 V to 12 V Operating Voltage: 5 V Flash Memory: 32 KB (out of which 2 KB used by bootloader) SRAM: 2 KB EEPROM: 1 KB Clock Speed: 16 Mhz Analog Input Pins: 8 Digital I/O pins: 22 PWM pins: 6 Max Current Per I/O pins: 40 mA Onboard 5V Regulator Package Includes: 1 x Arduino Nano Board R3 with CH340 Chip without USB Cable Compatible with Arduino (Unsoldered)
-
Sale!
BO Motor (Single Shaft/150 RPM )
Original price was: ₹110.00.₹95.00Current price is: ₹95.00.Add to cart- Low cost high performance,
- Use for science projects
- Dc geared motor,
- Operating voltage range of 3~12 volts dc,
- Good output torque capability,
- Rpm: Approximately 100 rpm,
Package Includes
- 1 x BO Motor (Single Shaft/150 RPM )
Reviews
There are no reviews yet.